Each line represents one transmission gear. Move your pointer across the chart to inspect speeds.
Swipe the chart horizontally to see all RPM values →
Hover a curve for details. Focus the chart and use ← / → to inspect RPM, or use the RPM controls below. Gear buttons toggle the same numbered gear on both transmissions in All Gears.
Based on the selected transmission's overall gear ratios.
Gear-by-gear speed
Drag the slider or hover the chart to inspect any engine speed.
5,000 RPM
Gear comparison at 5,000 RPM
Gear
Primary MPH
Comparison MPH
Change %
Change = (comparison speed ÷ primary speed − 1) × 100. Positive means faster at the same RPM, not faster acceleration. — means the numbered gear is unavailable; highest gears are not paired across different gear numbers.
Theoretical sequential upshifts
Uses the comparison / inspection RPM above as shift RPM. Assumes constant road speed and instantaneous engagement; excludes shift duration, clutch and torque-converter slip.
Gear
Overall ratio
Speed @ selected RPM
Speed @ 9,000 RPM
1,320 FEET · ONE SHARED TIMELINE
3/S Drag Strip Replay
NO RUN LOADED
Explore a supplied timeslip or replay a local ECU log. A timeslip constrains timing and distance; it cannot reveal the actual traction, RPM or shifts.
Replay recorded telemetry
CSV stays in this browser; it is not uploaded or saved. Required: numeric time, engine RPM and vehicle speed. At most 5 MB, 50,000 samples and 600 seconds. Missing values are not invented.
No file selected.
Optional throttle, MAP and wheel channels retain the source logger's numeric values and units unchanged. They are not normalized or used as vehicle speed. Gaps over 0.5 s remain unavailable.
Uses the transmission, comparison and tire settings above. Changing them clears the loaded run. Recorded logs retain their measured RPM; alternate gearing is not fabricated.
Build a simulated run or import a CSV to begin.
Play/Pause and Restart work with Enter or Space. Seeking pauses playback. Reduced motion keeps decorative rotation static; timeline playback starts only when requested.
The gear chart above follows the same operating point. Launch, slip and shift transitions can be off the ideal gear lines.
Inside the 3/S drivetrain
Front transverse 6G72 V6 · skeletal plan view · front of car at top
Animation is scaled, not real-time RPM. Pause provides a static equivalent; reduced-motion settings are respected. All four wheels roll on the road, even when only the front wheels are driven.
Transverse 6G72 V6 engine (driver side in reference)
Passenger-side front transaxle, beside and partly below engine
Separate AWD transfer case and rearward snout
Left and right front CV axles
Three-section propeller shaft with couplings
Carrier bearing #1 — support, not a gearbox
Carrier bearing #2 — support, not a gearbox
Rear differential
Left and right rear CV axles
Four wheels; rear AWS only on selected AWS chassis
Chassis selection changes the schematic only, never the gear ratios. Z11A is the factory model-code form; Z11 is shorthand. AWD and all-wheel steering (AWS) are separate systems. Market, model-year and equipment exceptions require VIN/service-document verification, particularly 1994 Stealth AWS; this is not a VIN decoder.
Power required: two different questions
Gearing determines theoretical speed per RPM, not whether the engine has enough power to reach it.
Maintain a road speed
Level road, still air, constant speed. Drag + rolling resistance at the wheels; estimated crank power includes the selected efficiency.
Vehicle and air assumptions
Starting assumptions, not measured specifications: 1,800 kg loaded VR-4, Cd 0.33, 2.0 m², Crr 0.015, 80% efficiency. Dry ideal-gas density from temperature and pressure; humidity, wind and grade excluded.
Quarter-mile trap-speed estimate
Empirical crank horsepower estimate: race weight × (trap MPH ÷ 234)³. Not a dyno measurement and not steady-speed power.
Reasonableness benchmark: 3,980 lb at 100–101 MPH gives approximately 311–320 hp. The 1994 VR-4 was rated at 320 hp; the Car and Driver test reports 3,810 lb curb weight and 13.9 seconds. Driver mass here is assumed; the archive's “1000 mph” trap is a transcription error, not accepted data.
Maintaining speed is not accelerating to that speed in a quarter mile. Real results depend on aerodynamics, race weight, traction, drivetrain losses, weather, tire growth, transmission slip and modifications. Neither estimate guarantees performance.
Parts, upgrades and services worth considering for your selected drivetrain and performance goals.
Refine your recommendations
For a closer match, check the linked listing with your vehicle year, engine, exact transmission and clutch/input-shaft details. Estimated horsepower alone cannot establish fitment or holding capacity.
Parts, Services & Support for Your 3000GT / Stealth
Engineering note: These are theoretical mechanical speeds, not predictions of real top speed. Calculations exclude tire growth, wheelspin, tire load/pressure effects, losses, engine power, aerodynamic drag, rev-limiter behavior, and automatic torque-converter slip. Tire revolutions per mile are input assumptions, not universal values for a nominal tire size. Always verify the specific drivetrain and tire before using results for a build.